Manufacturer: Yokogawa Electric Corporation
Yokogawa Temperature Controller TC10
General
The TC10 is a compact single loop temperature controller with easy-to-read 3 dynamic colors led display. The short depth of the controller helps save instrument panel space. The TC10 supports easy configuration with codes for quick start-up.
Yokogawa Temperature Controller TC10
Functional Specifications
Control Specifications
Control Mode: On/Off heating, On/Off cooling, On/Off with neutral zone (H/C),
PID heating, PID cooling, PID double action (H/C),Auto-tuning and Self-tuning algorithms, Overshoot control
Alarm Functions
Absolute high/low, Absolute inside/outside the band, Yokogawa Temperature Controller TC10
Sensor break, Deviation high/low, Deviation inside/ outside the band.
They are combined with Not active at power up, Latched, Acknowledgeable, and Not active at set point change for Deviation alarm.
Yokogawa Temperature Controller TC10
Digital Input Functions
Alarm reset, Alarm acknowledge, Hold of the measured value, Stand-by mode, Manual mode,
Heat with SP1 and Cool with SP2, Sequential set point selection, SP1/SP2 selection,
Binary selection of the set point, Work in parallel with Up/down key. Yokogawa Temperature Controller TC10
Communication Function
Interface type: Isolated (50 V) RS-485
Protocol: Modbus RTU
Baud rate: 1200, 2400, 9600, 19200, 38400 bps
Byte format: 8bit with no parity, one stop bit.
Instrument address: 1 to 25
Yokogawa Temperature Controller TC10
Model and Suffix Code
Yokogawa Temperature Controller TC10
|
Model Code
|
Suffix codes
|
Description
|
|
TC10
|
-N
|
o
|
C
|
o
|
o
|
o
|
D
|
o
|
F
|
|
Temperature Controller
|
|
Fixed code
|
-N
|
|
|
|
|
|
|
|
|
|
Always "-N"
|
|
Power supply
|
L
|
|
|
|
|
|
|
|
|
24 VAC/DC (Custom order)
|
|
H
|
|
|
|
|
|
|
|
|
100 to 240 VAC
|
|
Fixed code
|
C
|
|
|
|
|
|
|
|
Always "C"
|
|
OUT1 - 3
|
R
|
N
|
N
|
|
|
|
|
Relay output for ON/OFF control
|
|
R
|
R
|
R
|
|
|
|
|
Relay output with 2 alarm relays, for ON/OFF or Heat/Cool control with 1 alarm
|
|
V
|
N
|
N
|
|
|
|
|
DC Output for SSR
|
|
V
|
R
|
R
|
|
|
|
|
DC Output for SSR with 2 alarm relays or DCV and Relay output for Heat/Cool control with 1 alarm
|
|
V
|
V
|
R
|
|
|
|
|
2 DCV outputs for SSR with 1 Relay
(Custom order)
|
|
A
|
R
|
R
|
|
|
|
|
Analog output with 2 alarm Relays, or analog output and Relay output for Heat/Cool control with 1 alarm
|
|
IN/OUT4(Fixed code)
|
D
|
|
|
|
Always "D" - Selectable I/O (logic input / 12 V SSR drive output / 12VDC
20 mA transmitter power supply
|
|
Serial communication
|
S
|
|
|
RS485 Modbus
|
|
N
|
|
|
None
|
|
Fixed code
|
F
|
|
Always “F”
|
|
Option Code
|
/GK
|
Panel gasket for IP65
|
