Yokogawa Relay Board ARM55W[Product print page]

Product Name: Yokogawa Relay Board ARM55W

Product Type: ARM55W

Exhibitors: Yokogawa

Product Documentation: No Related Documents

Brief

Yokogawa Relay Board ARM55W, Yokogawa Relay Board ARM55W, for FIO, CENTUM VP.

Detailed description

Yokogawa Relay Board ARM55W

Manufacturer: Yokogawa Electric Corporation

Yokogawa Relay Board ARM55W

32 Wet Contact Outputs (M4 Terminals)

The Relay Board is used in FIO subsystem of CENTUM VP. Relay input/ output boards are connected in between digital input/output modules (for FIO) and field devices. Relay input boards receive contact signals or voltage input signals of field devices. Yokogawa Relay Board ARM55W Relay output boards receive output signals of the digital output module and amplify by the relay, and then output to field devices. These relay boards support dual- redundant digital input/output modules (for FIO). Yokogawa Relay Board ARM55W

STANDARD SPECIFICATIONS

lRelay Boards Detail Specifications

Mechanical Relay Boards (Contact Output)

Yokogawa Relay Board ARM55W

Models	ARM55D	ARM55W ARM55T (with switch)	ARM55C
Usage	Mechanical RelayDry Contact Output(“a” contact (NO)) (Single / Dual redundant)	Mechanical RelayWet Contact Output(Single / Dual-redundant)AUTO/OFF/ON switch(only for ARM55T)	Mechanical RelayDry Contact Output(“a” contact or “b” contact(NONC))(Single / Dual- redundant) (*6)
Contact Points	32-point	32-point	32-point
Terminals for Field Device Connection	M4 screws	M4 screws	M3.5 screws (*5)(M4 in power input part)
Modules	ADV551 (DO: 32-point) + ATD5A (Terminal block) ADV561 (DO: 64-point) (*1)	ADV551 (DO: 32-point) + ATD5A (Terminal block) ADV561 (DO: 64-point) (*1)	ADV551 (DO: 32-point) + ATD5A (Terminal block) ADV561 (DO: 64-point) (*1)
Signal Cables	AKB331 (for 32-point) AKB337 (for 64-point)	AKB331 (for 32-point) AKB337 (for 64-point)	AKB331 (for 32-point) AKB337 (for 64-point)
Maximum Load (*2)	250 V AC: 2 A per point 30 V DC: 2 A per point 125 V DC: 0.1 A per point (*3)	250 V AC: 0.6 A per point 30 V DC: 0.6 A per point 125 V DC: 0.1 A per point (*3)	30 V DC: 1.5 A per point
Minimum Load	5 V, 10mA	5 V, 10 mA	5 V, 10 mA
Power Supply Voltage and Current Consumption of Internal Circuit (require external power supply)	24 V DCMax. 0.65 A	24 V DCMax. 0.65 A	24 V DCMax. 0.85 A
Power Supply for Field Device (require external power supply)	-	Dual-line (supply power per 16-point) 250 V AC: Max. 9.6 A 30 V DC: Max. 9.6 A 125 V DC: Max. 1.6 A	-
Insulation Resistance	At least 10 MΩ (500 V DC)	At least 10 MΩ (500 V DC)	At least 10 MΩ (500 V DC)
Withstanding Voltage	Between field device terminalsand cases: 2 kV Between 24 V power terminalsand cases: 500 V Between 24 V power terminalsand field device terminals: 2 kV	Between field device terminalsand cases: 2 kV Between 24 V power terminalsand cases: 500 V Between 24 V power terminalsand field device terminals: 2 kV	Between field device terminalsand cases: 2 kV Between 24 V power terminalsand cases: 500 V Between 24 V power terminalsand field device terminals: 2 kV
Ambient Temperature and Humidity	0 to 50 °C, 10 to 90 %RH	0 to 50 °C, 10 to 90 %RH	0 to 50 °C, 10 to 90 %RH
Standards	Safety Standard [CSA] (*3) EMC standards [CE Marking],[C-Tick Marking]	Safety Standard [CSA] (*3) EMC standards [CE Marking],[C-Tick Marking]	EMC standards [CE Marking],[C-Tick Marking] (*4)
Size	W: 482.6 mm x H: 132.5 mm (3U)	W: 482.6 mm x H: 177 mm (4U)	W: 482.6 mm x H: 132.5 mm (3U)
Weight	2.2 kg	2.6 kg	2.2 kg

*1: Two sets of relay board (ARM55D, ARM55W, ARM55T, or ARM55C) and two sets of signal cable (AKB337) are required for one ADV561.

*2: For inductive loads, connect a spark killer (CR network for AC; diode for DC) in parallel with loads.

*3: For DC, 30 V or less is the requirement for the Safety Standard.

*4: ARM55C is out of scope of the Safety Standards.

*5: The applicable size of solderless lug is described below.