Yokogawa Direct Insertion Adapter ISC40FSJ-PCSJ
GENERAL
The
ISC40GJ, ISC40SJ sensors are designed for use with the FLXA21 2-wire Analyzer,
ISC202 2-wire transmitter and the ISC450G 4-wire converter. This combination
exceeds all expectations for conductivity measurement in terms of reliability,
accuracy, rangeability and price performance.
This
innovative inductive conductivity sensor provides highly accurate measurements
over a wide measuring range (1 μS/cm to 1999 mS/cm) and process temperature
range (-10 to 130oC, -10 to 105oC for ISC40SJ-TT) without changing the cell
constant and conducting recalibration.
The
erosion/abrasion resistant PEEK (Poly Ether Ether Ketone), which also features
excellent chemical resistance in all solutions except Fluoric Acid or Oxidizing
Concen- trated Acids.
The
PEEK sensor is provided with a rugged Stainless Steel mounting
thread/nut/gasket combination for ultimate flexibility in installation using
bulk head installation technique. There is also a wide range of holders and
options available for reliable in-line or off-line installation with double
O-ring seals for long service life of the sensor.
The
ISC40GJ, ISC40SJ have a large bore for optimal resistance to fouling processes
and when properly installed, the flow will keep the sensor clean, to help avoid
measuring errors.
FEATURES
Yokogawa Direct Insertion Adapter ISC40FSJ-PCSJ
•
Inductive Conductivity technique for elimination of fouling and polarization
errors.
•
Wide bore sensors for long term stability.
•
Installation flexibility due to wide range of holders and due to the use of
universal bulkhead construction.
•
A single sensor can maintain the high resolution and accuracy, and measure the
conductivity in an extremely brood range.
Minimum
span: 100 μS/cm
Maximum
span: 1999 mS/cm
APPLICATIONS
Yokogawa Direct Insertion Adapter ISC40FSJ-PCSJ
•
All applications where severe electrode fouling prevents the use of contacting
electrodes.
•
All ranges except (ultra) pure water applications.
•
All slurry applications where conventional systems suffer from plugging or
erosion.
•
All applications where the 6 decade rangeability is necessary for accurate
process control.
GENERAL
SPECIFICATION
Yokogawa Direct Insertion Adapter ISC40FSJ-PCSJ
1.
ISC40GJ, ISC40SJ Inductive Conductivity Sensor
Compatibility:
ISC40GJ
is compatible with FLXA21 2-wire Analyzer, ISC202G Inductive Conductivity
Transmitter and ISC450G Converter.
ISC40SJ-TT
is compatible with ISC202SJ Inductive Conductivity Transmitter.
Measuring
range: 1 μS/cm to 1999 ms/cm
Output
span: Minimum 100 μS/cm
Maximum 1999 mS/cm
Process
temperature:
-10 to 130 C for continuous exposure.
-10 to 105 C for ISC40SJ-TT. Suitable for steam-sterilisable
applications.
Process
pressure:
Dependent on installation; but <2 MPa (300
psi).
(Note) Process temperature and pressure
depend on specification of holders and adapters.
Process
flow: Maximum 5 m/s.
Wetted
materials:
Sensor: PEEK (Poly Ether Ether Ketone).
O-ring: Viton® or ethylene propylene
copolymer rubber.
Adapter (optional): SUS316 Stainless steel or
PVC or PVDF.
Non-wetted
materials:
Sensor thread: SUS304 Stainless steel.
Retaining nut: SUS304 Stainless steel.
Cable: Weatherproof vinyl.
Process
connection:
With retaining nut on G3/4 thread of sensor
top (refer to section Drawings and Dimensions) for bulkhead mounting; optional process adapters or process fittings.
Process
adapters:
JIS 10K 50 RF flange adapter (Material:
SUS316)
JIS 10K 50 FF flange adapter (Material: PVC
or PVDF)
DIN PN16 DN50 flange adapter
ANSI Class 150 2 flange adapter
R2 screw-in adapter
Cable
length: 5 m, 10 m, 15 m, 20 m
The length
into extension cable is inside of 50 m
Extension
cable cannot be used with ISC40SJ-TT.
Dimensions:
Refer to section Drawings and Dimensions.
Weight: Sensor: approximately 0.6 kg.
(Note) Do not submerge the sensor itself in process
water, as the seams between the mold and the metal of the sensor are not
waterproof. Since a temperature sensor is imbedded in the PEEK molded sensor,
its response speed is not fast. Install another temperature sensor if
necessary.
ISC40SJ-TT
Intrinsically safe type sensor
TIIS
certification sensor should be used with ISC202SJ Protection Concept and
Adapter Group: Ex ia IIC T4 Intrinsic safe rating:
Ui=14.4 V, Ii=20 mA,
Pi=190 mW, Li=28.6 mH, Ci=0.2 μF
Environment
and operational conditions
The temperature
of the sample solution in contact with sensor should be the range of -10 to 105
C.
2.
ISC40FDJ Immersion Holder
Process
temperature: Maximum 80 C.
Process
pressure: Maximum 0.2 MPa at 20 C.
Maximum
0.1 MPa at 80 C. Wetted materials:
Holder:
C-PVC or SUS316
O-ring:
Viton® or ethylene propylene copolymer rubber.
Flange (Optional) : PP or SUS316
Gasket:
Chloroprene or ethylene propylene copolymer rubber.
Process
connection:
Fixing
flange (Optional): DIN PN10 DN50 (ANSI 2 inch 150 lbs. with bolt holes):
Material PP
JIS 10K 50
RF: Material SUS316 2-inch pipe Mounting set (Optional): Zinc-plated steel.
3.
ISC40FFJ Flow Holder
Process
temperature:
ISC40FFJ-SA,
ISC40FFJ-SJ: Maximum 150 C.
ISC40FFJ-PA,
ISC40FFJ-PJ: Maximum 100 C.
ISC40FFJ-FA,
ISC40FFJ-FJ: Maximum 130 C.
Process
pressure:
ISC40FFJ-SA,
ISC40FFJ-SJ: Maximum 1.0 MPa at 150 C.
ISC40FFJ-PA,
ISC40FFJ-PJ: Maximum 0.6 MPa at 20 C.
ISC40FFJ-FA,
ISC40FFJ-FJ: Maximum 0.1 MPa at 100 C.
Maximum 1.0 MPa at
20 C.
Maximum
0.1 MPa at 130 C.
Wetted
materials:
ISC40FFJ-S口: SUS316
ISC40FFJ-P口: Polypropylene
ISC40FFJ-F口: PVDF
O-ring: Viton® or ethylene propylene copolymer
rubber.
Non-wetted
materials:
Nut:
SUS304
Mounting
set (Optional): SUS304
Flange adapters
(Optional): SUS304
Process
connection:
1/2NPT or
Rc1/2
DIN PN10
DN25 flange adapters (Optional)
JIS 10K 25
RF flange adapters (Optional)
4.
ISC40FSJ Direct Insertion Subassembly
Process
temperature:
ISC40FSJ-STWJ
: Maximum 110 C.
ISC40FSJ-SCWJ,
-SCSJ: Maximum 150 C.
ISC40FSJ-PCSJ
: Maximum 100 C.
Process
pressure:
ISC40FSJ-SCWJ,
-SCSJ: Maximum 1.0 MPa at 150 C.
ISC40FSJ-PCSJ:
Maximum 0.6 MPa at 20 C.
Maximum
0.1 MPa at 100 C.
ISC40FSJ-FCSJ:
Maximum 1.0 MPa at 20 C.
Maximum
0.1 MPa at 130 C.
Materials:
Wetted
materials:
ISC40FSJ-STWJ:
SUS316L, silicon rubber.
ISC40FSJ-SCWJ,
-SCSJ: SUS316, Viton® or ethylene propylene copolymer rubber.
ISC40FSJ-PCSJ:
Polypropylene, Viton® or ethylene propylene copolymer rubber.
ISC40FSJ-FCSJ:
PVDF, Viton® or ethylene propylene copolymer rubber.
Non wetted
materials:
ISC40FSJ-STWJ
: IDF clamp: SUS13.
ISC40FSJ-SCWJ, -SCSJ, -PCSJ, -FCSJ: Nut:
SUS304.
Process
connection:
ISC40FSJ-SCWJ:
coupling.
ISC40FSJ-SCSJ-PCSJ-FCSJ:
R2 screw-in coupling.
Dimensions:
Refer to
section Drawings and Dimensions.
5. BA20
Terminal Box
Use when
ISC202/FLXA21 transmitter or ISC450G converter is separated from ISC40口J
sensor and is set up.
Ambient
temperature: -10 To 50 C
Constructions:
IP54 agreement
Case
material: Article of cast metal of aluminum alloy
Cable
inlet: 2 (Pg13.5)
Case color : Straight
gray
Weight : Approx. 2 kg
(Note)
BA20 can not be used with ISC40SJ-TT.
6. WF10J
Extension Cable
Number of
mind Line: 6
Finish
outside diameter: 7.7 mm
Terminal
processing: Special terminals
Material:
Weatherproof vinyl.
(Note) WF10J cannot
be used with ISC40SJ-TT.
Yokogawa Direct Insertion Adapter ISC40FSJ-PCSJ
